650 Series Remote Microphone-Controlled Siren

Share This
  • Microphone controlled siren amplifier and light functions
  • Progressive 3-position “slide switch-like” button control
  • Backlit/rubberized microphone control head
  • Microprocessor-based amplifier with plug-and-play connections
  • (8) 10 A light and Aux relay positions
  • 100-watt output – WAIL, YELP, Priority, Manual (peak and hold) and Air Horn
  • Versatile microphone and amplifier mounting brackets
  • Remote on/off switch box with built-in PA volume control
  • Horn ring transfer
  • Installs quickly and is easy to operate
  • Three-year warranty
  • Compare all Police Sirens
Listen to this siren
Air Horn
Manual
Wail
Yelp

Features

Approvals

  • SAE J1849

Federal Signal’s innovative 650 series siren allows for all sound and light functions to be enabled by rubberized buttons located on the unit’s compact (4.5" L x 2" W x 1" H) and easy-to-use microphone control head. The advanced microprocessor-based amplifier exemplifies Federal Signal’s commitment to remain today’s unmatched leader in the field of siren technology.

Compact Microphone Controller
All siren and light functions are located on the 650 series microphone. Ten rubberized buttons control three progressive “slide switch-like” positions, on/off, PA, Air Horn, Peak-and-Hold, tone switching, and up to 30-amps of additional auxiliary power. The microphone controller “snaps” into a small plastic remote junction box where PA volume and a secondary on-off switch are located, then runs directly to the 650 series amplifier. Both of these connections are plug-and-play via eight conductor telephone jacks. An innovative microphone holder that can rotate and pivot to almost any angle allows for a wide variety of installation possibilities.

Advanced Amplifier Design
The 650 series remote siren provides 100 W speaker output and can operate from any 12 Vdc negative ground vehicle electrical system. It is short circuit protected and can be powered through an installed power distribution center (PDC), or directly from the vehicle’s battery. Reliability and efficiency are maximized by the use of advanced microprocessor-based technology. The 650 Series amplifier comes equipped with (8) 10 A light or auxiliary relay connections, is horn ring control ready, and has it’s own bracket mount to allow for quick and easy removal or replacement. Also provided is a 16.5-ft wire harness and all necessary hardware.

10 Button Controller Switch Operation

650 Siren Controller
OFF Turns off all enabled tone and light functions
PA Allows speech/RRB through vehicle’s speaker / overrides all other functions
TONE 650001 – Eliminates Wail tone when #3 is enabled
(priority tone can be enabled via HRT)
650003 – Switches tone between Wail and Priority when #3 is enabled
MAN Manual Peak-and-Hold / functions when all other tones are off
AH Air Horn
POS #1 Activates 10 A relay
POS #2 Keeps #1 enabled and activates second 10 A relay (progressive)
POS #3 Keeps #1 and #2 enabled and activates third 10 A relay (progressive)
AUX 1 Scrolls through (2) 10 A relays
AUX 2 Activates third AUX 10 A relay

Specifications

Audio Output power 100 W
Input Voltage 12 Vdc
Nominal Output Voltage 60 V peak-to-peak
Standby Current < 0.22 A
Input Current, Operating 10 A max
Operating Temp. -22˚ to +140˚ F (-30˚ to + 60˚ C)
Polarity Negative ground only
Frequency Range 725 to 1550 Hz

 

Physical Specifications
  Siren Amplifier Control Head
Length 8.5 in (21.6 cm) 4.5 in (11.4 cm)
Width 5.5 in (13.9 cm) 2 in (5.1 cm)
Height 2 in (5.1 cm)
(without base)
1 in (2.5 cm)

 

Ship Weight
  6.5 lb (3.0 kg) 0.5 lb (9.25 kg)
Warnings

Audible Equipment may produce LOUD sounds necessary to request the right-of-way. Audible equipment may cause hearing damage. Wear hearing protection. Refer to the Installation Manual or call 800/433-9132 for further instructions.

Important Warning for Police Boats and Fire Rescue Boats

It has come to our attention that police boat and fire rescue boat sirens and speakers may subject persons operating those craft to sound pressure levels that can cause permanent hearing loss. We recommend that speakers be located as far forward on the boat as possible, as recommended in the SAE Recommended Practice J1849 "Emergency Vehicle Sirens". However, unprotected exposures of a sufficient duration to properly located siren speakers can still create a risk of hearing loss.

It is our recommendation that your siren speakers should be relocated and persons operating these craft should wear hearing protection when using the siren system.

Failure to comply with these recommendations may result in temporary or permanent hearing loss to operators and passengers of these vehicles.

Ordering Info

Model Types
MODELDESCRIPTION
650001100-watt, microphone push-button controlled, full featured, wail/no wail tone activation, (8) 10-amp relay outputs
650003100-watt, microphone push-button controlled, full featured, wail-to-priority tone activation, (8) 10-amp relay outputs
650007100-watt, microphone push-button controlled, full featured, wail and yelp tone, (8) 10 A relay outputs, California Title 13 compliant
Replacement Parts
DESCRIPTIONPART NUMBER
Cable assembly, RJ45, 25-ftZ146903B
SIREN SUPPORT,AS-422/6SZ8615012A
CABLE HARNESS KIT, AS-422Z8615013A
CONNECTION BOX,AS-422/6SZ8615014A
CABLE,CONTROLLER,AS-422/Z8615015A
MIC,CONTROLLER,650001Z8615016A
MIC,CONTROLLER,650003Z8615016A-03
CONTROLLER MOUNT,AS-422/Z8615017A
RELAY OUTPUT CONN KITZ8615019A